Compression is one of those music production tools that is easy to understand, but tricky to master. It’s probably the most powerful tool in any mix engineer’s armory, with the ability to subtly enhance or radically transform the source audio, and is the signature processing to many a producer’s (and production genre’s) sound. By understanding the key controls and principals behind it you’ll be well on your way to using compression effectively in your mixes.

Along with Gating and Expansion, Compression is member of the Dynamics group of processors and works by affecting the dynamic range (difference between the loudest and quietest parts) of the audio passed into it. By effectively squashing the audio into a narrower dynamic range compression can produce results that are more controlled, sound fuller and sit more easily in a mix. And by tweaking controls such as the attack and release controls it’s also possible to use compression to shape the envelope of a sound.

The following controls are common to the majority of compressors . . .

Threshold / Input Drive
The threshold, normally expressed as a value in +/- Decibels (dB), determines the level above which the dynamic range is affected. Any audio that exceeds this threshold level will be squashed. Audio that falls below the threshold level will pass out of the compressor unaffected. Usually the threshold is completely variable, but some compressors (typically classic models) feature a fixed threshold and use the alternative of a variable input gain to drive the source audio into compression.

Ratio
The ratio control determines the severity of the squashing above the threshold level, and thus the shape of what is known as the ‘compression curve’. The higher the ratio the more kinked the compression curve becomes and the more squashed any audio that exceeds the threshold will be.

Together the Ratio and Threshold controls determine the style and severity of the compression. A low ratio / low threshold will typically give quite light and consistent compression, good for knitting a sound together or smoothing out a mix, whereas a high ratio / high threshold will be more suited to controlling volume peaks.

Gain Reduction Meter
Of course the squashing I’ve been referring to does have a technical name and unit of measurement, namely Gain Reduction, measured in dB. A compressor’s gain reduction meter is your window into how much squashing is going and aids setting a suitable threshold level.

Attack
The attack control simply sets the time, in milliseconds (ms), that it takes the compression to react after the threshold level has been exceeded. Setting a very fast attack time is great for controlling the peaks but can produce a more noticeably compressed sound. By using a longer attack time you can allow the initial peak through and compress the body of the sound which follows.

Release
As you’ve probably guessed the Release control determines how long it takes the compressor to stop reducing the signal once the level has fallen below the threshold. Release times are typically set a lot longer than the attack. In fact setting too sort a release time can lead to distortion on material with a lot of low end energy.

Most compressors (both hardware and software) will also feature some extra controls to help shape the style of compression. . .

RMS / Peak Sensing
The option to switch between Peak and RMS sensing is a feature of both the Logic Audio and Cubase bundled compressors. Essentially this control determines how the compressor perceives the level of the signal coming in. In Peak mode, even the shortest of signal spikes are heard and responded to which can be very useful for accurate dynamic control. But in reality the human ear doesn’t actually perceive short loud sounds and long loud sounds equally, working on a more averaging-over-time principal. Accordingly, in RMS mode short signal spikes will be reacted to less vigorously by the compressor, providing more natural sounding compression but allowing some spikes to pass through unchecked.
Threshold / Input Drive:
The threshold, normally expressed as a value in +/- Decibels (dB), determines the level above which the dynamic range is affected. Any audio that exceeds this threshold level will be squashed. Audio that falls below the threshold level will pass out of the compressor unaffected. Usually the threshold is completely variable, but some compressors (typically classic models) feature a fixed threshold and use the alternative of a variable input gain to drive the source audio into compression.

Ratio
The ratio control determines the severity of the squashing above the threshold level, and thus the shape of what is known as the ‘compression curve’. The higher the ratio the more kinked the compression curve becomes and the more squashed any audio that exceeds the threshold will be. So a ratio of 1.2:1 (fig. A) will very subtly affect the dynamic range, whereas a ratio of 6.1:1 (fig. B) will produce significantly more gain reduction for the same threshold setting.

Together the Ratio and Threshold controls determine the style and severity of the compression. A low ratio / low threshold will typically give quite light and consistent compression, good for knitting a sound together or smoothing out a mix, whereas a high ratio / high threshold will be more suited to controlling volume peaks.

Knee
The Knee control affects the shape of the compression curve. A ‘Hard’ Knee setting will produce results as we have described so far where above the threshold audio is squashed equally depending on the compression ratio. A ‘Soft’ Knee setting smooths the kink in the compression curve so that around the threshold level the compression ratio gradually rises to reach the ratio set. In general Hard Knee compression will be better for peak limiting and surgical work, whereas a Soft Knee will produce more characterful results.

Stereo Link
If you are compressing a stereo signal you would normally like the left and right sides to be compressed equally to retain the original stereo image. (i.e left and right are linked). However, for some specialist applications and in you want to use the two channels of a stereo compressor independently for two mono signals, unlinked mode is desirable.

Compression In Practice
In practice compression can be either a very transparent tool for controlling dynamics or an obvious effect, adding character to a sound, and it’s the interaction of all the controls described above that determine which flavor you get. If you’re just getting started then it’s probably best to think of compression as having two basic applications; ‘peak control’ and ‘thickening’. And you can apply these two compression types to any mix element in the way I’m about to describe with some great results.

Peak Control
It’s best to place this first in the compression chain, after any corrective EQ, gating or filtering you might have done. Set your attack time to 0ms (or as near as is possible) and a release time of around 80ms. The release should be varied according to the material. For drums a shorter time may work better and for instruments will a lot of low end energy, like Bass Guitar, a longer release time (say 200ms) may be more appropriate. Set your Compression Ratio to 4:1 and then adjust the threshold to give around 3dB of gain reduction on the peaks.

Thickening
Thickening compression should follow Peak Control. This time we want to allow some of the initial attack of the sound through and just gently even out the overall dynamics, so set an attack time of between 15 to 50ms and a release time of 250 to 350ms. Set the Compression Ratio to 1.4:1 and again adjust the threshold to give around 3dB of gain reduction. If your compressor features a Peak / RMS option, then opt for RMS here.

Quality Music radio: DATABLENDER FM

4411
Tv

PressPausePlay

5230
Tv

How to create wide open mixes

6853
Production

Seven ways to reduce noise

8714
Production

Mixing - the 12 step program

8112
Production

Arrangement 101

5643
Production

Tips for mixing the low end

5895
Production

The audible frequency range

6321
Production

Mastering basics for musicians

7472
Mastering

10 questions about mastering your recordings

5875
Mastering

Preparing your mixdown for mastering

5690
Production

Tips for mixing for vinyl

9923
Production

Gez Varley

7038
Interview, synthience

Viktoria Rebeka

5402
Interview, synthience

Andy Wonderland

4898
Interview, synthience

Andrea Suglia

5372
Interview, synthience

Mikrokristal

6317
Interview, synthience

Luke Hess

5721
Interview, synthience

Stereo editing and mastering

5904
Mastering

Preparing music for mastering

5887
Mastering

How the professionals do it

5539
Mastering

Audio mastering in your computer

6074
Mastering

T-Racks mastering audio techniques

10812
Mastering

Digital audio editing

5945
Production

6 mono to stereo methods

5550
Production

Outboard processing

5447
Production

Mixing on headphones

5898
Production

Using the side-chain

4988
Production

Watch your levels

5178
Production

Parallel compression

5720
Production

The sub-kick trick

6537
Production

5 perspective tips

5292
Production

Vocals in the Mix

5366
Production

Panning Tips

5962
Production

Using Compression

5350
Production

Tech Talk - Sherman Filterbank

7621
Tv

Tech Talk - Funktion One

6736
Tv

The Creation of Techno Music

5985
Tv

Mixing for vinyl record

6026
Production

20 tips on home mastering

6947
Mastering

18 ways to give your music groove

8480
Production

23 tips for better home recordings

7770
Production

48 ambient production tips

14295
Production

30 EQ techiques

9302
Production

35 music production pro tips

9565
Production

Pre master levels

11230
Mastering

9 mastering tips for beginners

9791
Mastering

20 tips on music mixing

8383
Production

8 synthesis tips for beginners

7675
Production

Your guide to frequency

16271
Production